Call Now For a Free Consultation: +1(604)267-0255
You are here: Home » Products » Corner Beads » Corner Beads

Hot Products

Share to:

Corner Beads

Our Corner Bead is made of galvanized aluminum and stainless steel.
Now we have 27 types for corner beads in terms of features.

All the available specifications are presented in "VARIATION".
Any other specifications can be customized.

Quantity:
  • Duke's Wire Mesh

Our Corner Bead is made of galvanized alumimium and stainless steel. Now we have about 60 types for corner beads in terms of featur.

USAGE: 

Apply for surfacing and plastering stages. Apply to both interior and exterior use Position at door edge, column, girder, wall edge corne

Unite with cement rendering. Forming right angle, rounded edge, regular straight Limit edge chipping Increase speed in execution

Installation:

Installing corner bead is a fairly simple intermediate step between hanging wall corner and the beginning of your wall corner taping and mudding steps.

Necessary Drywall Supplies & Tools

Metal Corner Bead

Tin Snips

Tape Measure

Screw Gun or Drill

11/2” screws

Corner bead is available as either galvanized metal or PVC(plastic). We prefer to use metal, as plastic occasionally cracks during the fastening  process and also provides less protection to your corners. So Daye Corner Bead is a must for your home decorations.

 

Applying Cut the bead:

#1- Cut the Bead

Measure the length with a tape measure and cut a piece of bead for each outside corner. Use a pair of tin snips to cut in from each side of the metal and then bend it in the middle to break it apart.

#2- Fasten with Drywall Screws

Hold   the bead against the corner while pressing hard on the peak with your palm to flatten it tightly to both walls. start near the top and drive a 158 or 2 inch drywall screw through one of the small holes in the metal and into the wall frame Drive a screw into the opposite wall at about the same level, but not directly across, to hold the bead in two places. Sink the heads of the screws deep enough to slightly kink the metal and make a small depression in the drywall. If the screws are not driven far enough below the surface of the wall, the heads will show through the mud and beery visible Move along the length pressing at each point and driving the the screws at about 12 inch intervals along both walls. Check to be sure the metal is flat the full length of the wall. Run a joint knife over it to check for any spring in the metal and drive a screw at any loose edges.

 

#3- Apply Joint Compound

Use a 6 inch drywall joint knife to apply a thick coat of setting-type joint compound in crossing strokes along both walls, from one end to the other. Use a very thick coat that covers all the metal and spreads well onto the thedrywall Remove the excess mud to float the surface into the corner. Rest one side of the knife blade on the bead peak and the other against the drywall. There will be a slight dip in the wall where the two meet, float the knife over this dip to fill it in with a solid coat of mud. stroke starting at the end and keep the knife straight as it rides along both surfaces. Dont push too hard on the blade to avoid bending it and causing a depression in the mud coat. Float the blade to keep the mud as level as possible

  

#4- Smooth Out the Corner

Float the other wall in the same way. Clean the mud off the joint knife frequently as you work to avoid buildup. When you finish, go back to the start and run the clean blade along the whole length of each wall again in one smooth stroke to leave a level surface. Skim along the wall edge of the mud to remove any buildup there and blend it flat before moving on This will insure you don t have to do a lot of extra sanding at the edges when you re done sanding too hard at the edges can tear into the surrounding drywall paper, which would then need to be repaired Before leaving the mud to set, scrape the peak of the corner by running the knife blade upward to cut it off. when you're done, let the mud set he label or just wait until it feels solid.

 

5-Apply a Second Coat of Mud

When the mud is completely hard, use a larger joint knife to apply a second coat using ready-mixed compound. First scrape over the hardened mud with the blade to knock off any rough spots and then apply a thick coat of compound onto both wall surfaces. Use crossing strokes to cover the corner completely and overlap the wall edges of the first coat smooth the mud starting at one end and stroke all the way to the other.Use light pressure to avoid bowing the knife blade. Skim the excess mud from one wall at a time working ceiling to floor, and then do the same on the

very light pressure to catch any pits or scratches and smooth the surface. Let the mud dry for about 12-24 hours and check the finish. If there are pits and scratches in the dry mud, apply another coat and skim it off in the same way. when the final mud coat dries, sand it lightly with medium grit sandpaper using light pressure along the edges to avoid tearing into the drywall paper.


corner beadscorner beads1corner beads2corner beads3corner beads4

Application:

The corner bead with fiberglass mesh has been widely used in all kinds of outdoor andindoor of building to protect the wall corner.

It is molded and extruded with rigid PVC compounds. It can be used for exterior and interior wall corner. 

The standard corner beads specification:


Corner-Beads Corner-Beads2 Corner-Beads1
Corner-Beads4 Corner-Beads5 Corner-Beads3

Contact Us

we

 Tel:+1(604)267-0255
 E-mail: info@dukeswiremesh.com
 Add: 1295 W 75th Ave, Vancouver, BC, Canada V6P 3G4

Product Inquiry

Duke's Wire Mesh Supply Services Ltd.

QUICK LINK

CATEGORY

CONTACT INFO

Main: +1(604)267-0255
 Tel: +1(778)999-7925
  E-mail: info@dukeswiremesh.com
  Add: 1295 W 75th Ave, Vancouver, BC, Canada V6P 3G4

SUBSCRIBE

Be the first to know about our lastest products.
 Copyright 2017 Duke's Wire Mesh Supply Services Ltd. All rights reserved. Support by Rongchuangmedia​